Setting up A Bathtub
Setting up A Bathtub
Blog Article
This post below involving A Step-by-Step Guide to Installing a Bathtub is exceedingly compelling. Read it for your own benefit and see what you think about it.
Installing a bathtub isn't precisely brain surgery, however it does call for solid plumbing, carpentry, and sometimes, tiling skills. Changing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is easily obtainable, the project can move immediately; if you need to open up a wall to remove the old tub as well as place the brand-new tub, the job is a lot harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need a helper to leave the old bathtub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task and also fit trying it. As opposed to hiring a contractor to take over a halfway-completed project, it is better to think about utilizing one before you begin. Chances are you might require a specialist plumber to make tube links.
This article will help you install a new bathtub in your bathroom if you have already acquired a new bathtub as well as don't require to alter the setup of your previous water system pipes.
Your devices as well as product checklist should make up the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted accessibility that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the remaining water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin making sure that the washers are in place between the tap as well as the sink. Safeguard the faucet in place with the maker supplied backnut. As soon as the faucet is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet ports. The previous kind should be connected to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little points.
The next objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out degree.
To install taps, fit all-time low of the outermost adaptable tap port to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Activate the water and check all joints and also new pipework for leaks as well as tighten them if needed. Load the bathtub and likewise inspect the overflow electrical outlet and also the regular outlet for leaks.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bathtub should wait until the bathtub has been utilized a minimum of once as this will settle it right into its last placement.
Planning for the Installment
Firstly, the sustaining framework provided with the bathroom must be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make certain that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps system to avoid stress on the bathtub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final placement.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split a rigid seal, triggering the water to penetrate the wall surface in between the bath as well as the tiling, leading to issues with wetness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to blend in your components as well as installations. They are sold in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water before securing, to allow for the motion experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles using waterproof or water-proof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that write up about How to Install a Bathtub while doing a search on the web. Sharing is nice. You never know, you will be helping someone out. I enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Schedule Free Estimate
Report this page